Duplex Steel 2205 Strips, UNS S31803 Strips Supplier & Exporter

DUPLEX STEEL UNS S310803 STRIP GENERAL PROPERTIES:

Duplex Steel 2205 Strip is a two-phase, ferritic, austenitic 22% chromium, 3% molybdenum, 5 to 6% nickel alloyed stainless steel. It is the most widely used duplex stainless steel grade and is characterized by high yield strength, double that of the standard austenitic stainless steel grades. It also demonstrates good fatigue strength, as well as outstanding resistance to stress corrosion cracking, crevice, pitting, erosion, and general corrosion in severe environments.

Harsh steel Export and Supply Duplex Steel UNS S31803 Strip capabilities include:

• Duplex Steel UNS S31803 Strip Annealed & Precision
• Duplex Steel UNS S31803 Strip thickness-0.1mm to 6.00mm
• Duplex Steel UNS S31803 Strip width-2.5mm to 1320mm (slit to close tolerances)

Harsh steel provides Duplex Steel UNS S31803 Cold rolled mill finish strip such as:

• Duplex Steel UNS S31803 Strips 2D - cold rolled, heat treated, pickled.
• Duplex Steel UNS S31803 Strips 2B - cold rolled, heat treated, pickled, skin passed on bright rolls.
• Duplex Steel UNS S31803 Strips 2R(BA) - cold rolled, bright annealed
• Duplex Steel UNS S31803 Strips HR - hot rolled, annealed

DUPLEX STEEL UNS S310803 STRIP APPLICATION:

• Chemical processing, transport and storage – pressure vessels, tanks, piping, and heat exchangers
• Oil and gas exploration and processing equipment – piping, tubing, and heat exchangers
• Marine and other high chloride environments
• Effluent scrubbing systems
• Pulp and paper industry – digesters, bleaching equipment, and stock-handling systems
• Cargo tanks for ships and trucks
• Food processing equipment
• Biofuels plants

DUPLEX STEEL UNS S310803 STRIP COROSSION RESISTANCE:

• Due to its high chromium, molybdenum, and nitrogen content, Duplex 2205 demonstrates superior corrosion resistant properties to 316 and 316L in most environments
• Chromium, molybdenum, and nitrogen content also provide high resistance to pitting and crevice corrosion, even in oxidizing and acidic solutions
• Resistant to chloride stress corrosion cracking and temperatures of up to about 302°F (150°C)
• The presence of ferrite provides for good performance of Duplex 2205 in caustic environments

DUPLEX STEEL UNS S310803 STRIP HEAT RESISTANCE:

• Similar to other duplex stainless steels, Duplex 2205 has good oxidation resistance at high temperatures
• Subject to embrittlement when exposed to temperatures above 572°F (300°C) even when exposed for short periods of time; Duplex 2205 is therefore not recommended for use above 572°F (300°C)

DUPLEX STEEL UNS S310803 STRIP WELDING CHARACTERISTICS:

• Possesses good weldability
• Should not generally be welded without filler metal as this may result in excessive ferrite

DUPLEX STEEL UNS S310803 STRIP HEAT TREATMENT:

• Annealing temperature range is 1868 to 2012°F (1020 to 1100°C)
• Cannot be hardened by heat treatment – but Duplex 2205 does work-harden
• Special consideration is needed to compensate for a higher coefficient of thermal expansion to avoid warping and distortion

DUPLEX STEEL UNS S310803 STRIP PROCESSING - HOT FORMING:

Most Duplex 2205 producers recommend a maximum hot forming temperature between 2010 and 2100°F (1100 to 1150°C). If the shape of the work piece is not compact, the edges may be significantly cooler than the bulk, and there is risk of cracking in the cooler regions.

DUPLEX STEEL UNS S310803 STRIP PROCESSING - COLD FORMING:

Duplex 2205 has shown good formability in a variety of fabrications. The high strength of Duplex 2205 can pose problems. Even when the equipment has sufficient power, allowance must be made for higher spring-back caused by the grade's high strength.

DUPLEX STEEL UNS S310803 STRIP MACHINABILITY:

Duplex 2205 is somewhat more difficult to machine than the 300 series austenitic stainless steels. Higher cutting forces are required and more rapid tool wear is typical. Some guidelines for machining are: A) Use powerful, rigid machines with extremely strong rigid mounting of tools and work piece, B) Minimize vibration by keeping the tool extension as short as possible, C) Use a nose radius on the tool, no longer than necessary, for carbides that have a sharp edge while still providing adequate strength, D) Design machining sequences to always provide for a depth of cut below the work hardened layer resulting from the previous passes.

Harsh steel Supplies and Exports Duplex Steel UNS S31803 Strip from 2.5mm wide to 400mm, slit to close tolerances. We supply in below specifications: -

Harsh steel provided the Specification of Duplex Steel UNS S31803 Strip as below: -

• Material is manufactured on a bespoke basis to the customer's individual needs and hardness.
• Material can be supplied in coil or length form
• Hardness of material to customer's specific requirements.

We export our DUPLEX STEEL UNS S31803 STRIPS products to Western and Eastern Europe, Saudi Arabia, Bangladesh, United States, United Arab Emirates, Canada, Angola, Argentina, Austria, Azerbaijan, Pakistan, Peru, Chile, Spain, France, United Kingdom, Indonesia, Israel, Iran, Kuwait, Mexico, Malaysia, Nigeria, Serbia, Singapore, Taiwan, Chile, Venezuela, Ecuador, Netherlands, Brazil, Colombia, Ghana, Iran, Denmark, Poland, Australia, Afghanistan, Bahrain, Costa Rica, Egypt, Iraq, Jordan, South Korea, Kazakhstan, Sri Lanka, Lithuania, Norway, Oman, Philippines, Poland, Qatar, Russia, Vietnam, South Africa, Nigeria, Mexico, Turkey, Hungary, Algeria, Belarus, Belgium, Bhutan, Bolivia, Bulgaria, Croatia, Czech Republic, Estonia, Finland, Greece, Italy, Japan, Libya, Romania, Thailand, Trinidad & Tobago,Tunisia, Ukraine, Yemen, Hong Kong, Gabon, China, Portugal, Switzerland, New Zealand, Sweden, Slovakia, Kenya, Lebanon, Morocco, Mongolia etc. We are sure that we also can cover the requirements requested by your company you can email us at harshsteel@ymail.com for your instant requirements.

Enquiry